Formwork systems

Sort by:

Schalungsbinder SAM 2

Suitable for Standard formwork panels width 25, 50 and 100 cm. multiple reusable binder made of steel strip. The length 100 cm is reinforced in the middle.

SAM-Pull out lever

Pull out lever to remove the end of spacer after stripping the formwork. Suitable for normal and exposed concrete.

SAM-Pull hammer

to pull out the spacer-end after stripping the formwork. Suitable for normal concrete and exposed concrete.

SAM-calibrating crank

to break off the end of the spacers after stripping the formwork. !not suitable for exposed concrete!

H-extensions

To mount at the undermost formwork panel if worked with joint tape.

SAM-spacer normal

Spacer system SAM for normal concrete.(no exposed concrete surface - the walls should be plastered or coverd afterwards) Easy and fast application, in combination with 27 mm Standard formwork panels. Package units:to wall thickness 50 cm 100 pcs. / Packfrom wall thickness 51 cm 50 pcs. / Pack Other special lengths (in cm downgrading) from 6 - 300 cm possible.

SAM-spacer; without wedge

Spacer System SAM for visible concrete. In combination with 27 mm Standard formwork panels, fast and easy usage. Package units: to wall thickness 30 cm 100 pcs. / carton from wall thickness 31 cm 50 pcs. / carton Economical stripping of concrete - retaining walls. Exposed concrete not attached! All special lengths (in cm downgrading) from 6 - 300 cm possible.

SAM-Abstandhalter; Sicht aufg.

Abstandhalter System SAM für Sichtbeton (Sichtbeton Qualität) In Kombination mit 27mm Standard Schaltafeln, schnell und einfach anwendbar. Verpackungseinheiten:bis Wandstärke 30 cm 100 Stk. / Kartonab Wandstärke 35 cm 50 Stk. / Karton Das SAM Schalungssystem ermöglicht ein unkompliziertes und sparsames Schalen von Betonmauern. Alle Sonderlängen (in cm Abstufungen) möglich.

SAM-Plastic taper locks

Plastic Taper locks after removing the spacer the wedge closes the exposed concrete element. The result is an attractive exposed concrete surface.

SAM double wall connector

Double wall connectors The simple but effective solution for formwork panels

Abstandhalter für Schienenschalung mit Nocken

Abstandhalter für Schienen System mit Noppen. Mit aufgesteckten Kunststoffelementen für Sichtbeton Oberflächen.

Keilklammer Typ F verz.

Passend für folgende Schalungssysteme Framax Mammut Master

Vitzthum-Baurohr QUADRAT

Concrete form for square pillars. Easy stripping through integrated division line.

Vitzthum-Baurohr RECHTECK

Formwork tube for rectangular columns Standard lengths 3m and 4m Other lengths on request!

Vitzthum-formwork TUBE PLUS

Tube Plus guarantees a smooth surface. The inside of the shuttering tube is covered with a smooth film. Other lengths on request!

Vitzthum-Baurohr Standard-Spiral

Concrete form round in spiral version. Other lengths on request!

Concrete formwork mounting kit

Concrete formwork mounting set including: 1 x Tensile belts length 4,0 m 2 x Threaded subplate Ø 15 mm, 2 x Wing nuts Ø 15 mm

Deckenstütze Stabil (DC) nach EN 1065

Produced and tested according to EN 1065, with covered thread (DC). Props in different sizes and versions. With failure protection and accident proof. Headplate: class A 120 x 120 x 6 mm, with borehole Ø 40 mm G-hook: Ø 14 mm (no loosing) with bearing ring.

Deckenstützen Euro (DC) nach EN 1065

All versions with failure protection, accident proof. Props in different sizes and versions.Failure loads tested according to EN 1065. Produced and tested according to EN 1065, with covered thread (DC). With failure protection and accident proof. Threaded socket with additional bearing ring (slide ring). Headplate: class A 120 x 120 x 8 mm, with borehole Ø 40 mm G-hook: Ø 14 mm (no loosing) with bearing ring.

Deckenstütze Euro (DO) nach EN 1065

Produced and tested according to EN 1065, with visible thread (DO). With failure protection and accident proof. Headplate: 120 x 120 x 8 mm, with borehole Ø 40 mm Headplate: * 140 x 140 x 8 mm, with borehole Ø 40 mm G-hook: Ø 15 mm (no loosing).

Baustütze - Mini (DC)

With covered thread (DC). Headplate: 120 x 120 x 5 mm, with borehol ø 40 mm G-hook: Ø 12 mm (no loosing) with bearing ring (loose) Failure loads tested at concentric load, pay attention to security factor!

Lower-Prop head, galvanised

Suitable for props for hole Ø 40 mm. For wood formwork beams H 20

Dreifuß-Ständer für Stützen

Suppliable with a galvanised or lacquered surface.

Aussparungs-Innenecken

Inner corner made of steel with clamping screws Ø 15 mm For shaft formwork, ceilings- door- and wall-recess Easy and fast mounting and dismantling For wooden formwork 12 - 35 mm thickness The fast and universal solution for your construction site