Properties
| Länge in mm: | 72 mm |
|---|---|
| Tragkraft: | 28 kN |
| für Ankerstab ø: | 15 mm |
Uni Concrete Sleeve Ø 15 mm Three-Piece PA66GF30
Description
Anchor sleeve UNI Ø 15 mm three-part made of PA66GF30
With internal winch for Ø 15 mm Dywidag tie rod.
Ideal use for fastening slab edge formwork, consoles, scaffolding, guardrails, etc.
Permissible load 28KN
Properties
| Länge in mm: | 72 mm |
|---|---|
| Tragkraft: | 28 kN |
| für Ankerstab ø: | 15 mm |
Zubehör
Nagelflansch mit Nagel für Uni Betonhülse (Art.Nr. 65U)
Sealing plug after removal of the mounting equipment.
Ankerhülse Alu (Art.Nr. 65UA) und Uni Betonhülse (Art.Nr. 65U).
Ähnliche Artikel
With internal thread for Ø 15 mm Dywidag tension rod.Perfect use for fastening slab edge formwork, consoles, scaffolding, guardrails, etc. Permissible load: 28 kN.
Customers also viewed
With internal thread for Ø 15 mm Dywidag tension rod.Perfect use for fastening slab edge formwork, consoles, scaffolding, guardrails, etc. Permissible load: 28 kN.
With internal thread for Ø 15 mm Dywidag tension rod.Perfect use for fastening slab edge formwork, consoles, scaffolding, guardrails, etc. Permissible load: 28 kN.
With internal thread for Ø 15 mm Dywidag tension rod.Perfect use for fastening slab edge formwork, consoles, scaffolding, guardrails, etc. Permissible load: 30,5 kN with concrete strength of 17 N / mm².
Ankerhülse Alu (Art.Nr. 65UA) und Uni Betonhülse (Art.Nr. 65U).
The flexible, compressible PE Spiral Spacer Tube 22/28 has been specially developed for use in challenging formwork conditions. The spiral tube can be used in combination with a plastic spacer tube or an FB wall thickness spacer. It provides a practical and adaptable solution, particularly for single-sided formwork, uneven surfaces, and irregular tie rod positions, such as those encountered on rock faces or in excavation pits. Thanks to its special spiral structure, the tube can be compressed by applying axial pressure, allowing it to adapt flexibly to different spacing requirements. At the same time, it offers greater rigidity than conventional PE tubes. This makes it easier to unscrew and remove the formwork tie rod after concreting. Another advantage is the ease of adjusting its length: the spiral spacer tube can be cut to the required length directly on the construction site, even during formwork assembly, using a suitable cutting tool. With an internal diameter of 22 mm, the spiral tube is designed for use with Ø15 mm formwork tie rods.
With internal thread for Ø 15 mm Dywidag tension rod.Perfect use for fastening slab edge formwork, consoles, scaffolding, guardrails, etc. Permissible load: 28 kN.
Spacer tube with a roughened surface and an inner diameter of 22 mm. The roughened surface ensures improved adhesion to concrete. Chemical Resistance: Mineral oils (aromatic-free) Motor oils
AS-Fugenbänder aus Weich - PVC bestechen durch Ihre Vielzahl an guten Eigenschaften und durch hohe Wirtschaftlichkeit. Die spezielle Werkstoff-Mischung macht das Fugenband einsatzfähig im Sommer und Winter (Härte). AS-Fugenbänder eignen sich für alle normalen Beanspruchungen und decken somit den größten Teil der Beanspruchungen bei Bauwerken ab. Arbeitsfugenband bzw. Silofugenband einfach von Hand in den noch weichen Beton eindrücken.
One-piece formwork spacer tube with two sealing plugs, ensuring the specified wall thickness reliably. Spacer tube / cone system tested for watertightness up to 5 bar Fire resistance tested in accordance with EN 1363-1 Complies with the requirements of the W1 guideline
Formwork stop made of fibreglass. Pins Ø: 10 mm; Length: 100 mm ADVANTAGES: Non-corrosive High strength and stable Chemical resistance Fast and easy installation INSTALLATION: Mark the position of the formwork with a snap line. Drill periodically holes with a diameter of 10mm along the marking. ATTENTION: Please consider the length of the pins.