Go to homepage
Catalogue
Wishlist
Request Basket
Categories
Skip image gallery
Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm

Properties

Medium pipe Ø: 277 - 280 mm
Verstellbereich in mm: 277 - 280 mm
ø in mm: 400 mm

Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm

Product number: 61LXNC400ND277

Available on request

ø in mm
Medium pipe Ø

Price on request

Stk

Description

  • Annular seal Basic 1 made of stainless steel, V2A (material no.1.4301)
  • Seal width 40 mm for pressing water up to 2.5 bar
  • completley gastight and watertight
  • built-in torque control
  • EPDM rubber insert


DIVIDING THE RING SEAL BASIC 1

  • To split the annular seal Basic 1, loosen and remove a screw.
  • Unfold the front and rear press segment and cut the rubber press ring radially about 10 mm to the left or right of the screw hole with a sharp knife.

Properties

Medium pipe Ø: 277 - 280 mm
Verstellbereich in mm: 277 - 280 mm
ø in mm: 400 mm
Filter products
Variants

With the help of our variant list you can find your article faster and easier.

Product Nr.
Product
Medium pipe Ø
ø in mm
Price
Action
61LXNC125ND060
 Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm
60 - 63 mm
125 mm
61LXNC150ND088
 Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm
88 - 92 mm
150 mm
61LXNC200ND110
 Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm
110 - 112 mm
200 mm
61LXNC200ND125
 Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm
125 - 127 mm
200 mm
61LXNC200ND139
 Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm
139 - 140 mm
200 mm
61LXNC200ND159
 Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm
159 - 162 mm
200 mm
61LXNC250ND159
 Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm
159 - 162 mm
250 mm
61LXNC250ND210
 Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm
210 - 210 mm
250 mm
61LXNC300ND200
 Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm
200 - 200 mm
300 mm
61LXNC300ND250
 Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm
250 - 250 mm
300 mm
61LXNC400ND277
 Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm
277 - 280 mm
400 mm
61LXNC400ND315
 Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm
315 - 319 mm
400 mm
61LXNC400ND324
 Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm
324 - 326 mm
400 mm
61LXNC150ND110
 Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm
110 - 112 mm
150 mm
61LXNC250ND200
 Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm
200 - 200 mm
250 mm
Skip product gallery

Customers also viewed

Kunststoff-Futterrohr WELLO mit Quellband

WELLO, the lining tube made of PE with an all-round swelling coating. The tube is smooth inside. The undulating outside clings to the concrete. Two swelling tapes applied around the center also prevent water from entering the structure Wello casing, double security through corrugation and swelling tape, sealing by means of an annular seal. Tested up to 30m water column.

Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm

Annular seal Basic 1 made of stainless steel, V2A (material no.1.4301) Seal width 40 mm for pressing water up to 2.5 bar completley gastight and watertight built-in torque control EPDM rubber insert DIVIDING THE RING SEAL BASIC 1 To split the annular seal Basic 1, loosen and remove a screw. Unfold the front and rear press segment and cut the rubber press ring radially about 10 mm to the left or right of the screw hole with a sharp knife.

Ringraumdichtung Basic 1 - Dichtungsbreite 20 mm

Annular seal Basic 1 made of stainless steel, V2A (material no.1.4301) Seal width 20 mm for non-pressing water up to 1.5 bar completely gastight and watertight built-in torque control EPDM rubber insert DIVIDING THE RING SEAL BASIC 1 To divide the press seal Basic 1, loosen and remove a screw. Unfold the front and rear press segment and cut the rubber press ring radially about 10 mm to the left or right of the screw hole with a sharp knife.

Ringraumdichtung Basic 1 - Dichtungsbreite 20 mm

Annular seal Basic 1 made of stainless steel, V2A (material no.1.4301) Seal width 20 mm for non-pressing water up to 1.5 bar completely gastight and watertight built-in torque control EPDM rubber insert DIVIDING THE RING SEAL BASIC 1 To divide the press seal Basic 1, loosen and remove a screw. Unfold the front and rear press segment and cut the rubber press ring radially about 10 mm to the left or right of the screw hole with a sharp knife.

This website uses cookies to ensure the best experience possible. More information...