Properties
| Abmessung in mm: | 2100 x 2400 mm |
|---|---|
| Material: | PP (Polypropylen) |
| Stärke in mm: | 10 mm |
VIBA Plex F Formwork Board 10
Description
The board is a universal usable and cost-effective shuttering for single and strip foundations. The structure of the board allows the absorption of a lot of pressure and by cutting in one side of the baord, it can be easily bent around corners. Board size: 5.04 m²
Advantages:
- low dead weight of the plate
- assembly possible without crane and other aids
- prefabricated foundations with low installation time
- environmentally friendly, not hazardous to water, material recycling possible
- single or strip foundations can be made easily without additional tools
- no abherent required
- dimensionally stable
Properties
| Abmessung in mm: | 2100 x 2400 mm |
|---|---|
| Material: | PP (Polypropylen) |
| Stärke in mm: | 10 mm |
Customers also viewed
Three layer plywood weather-resistant glued Surface with melamine-resin (yellow). Other colours on request. Special formats on request Additional millings possible! All standard cuts are possible!
Shuttering element for joint seal sheet (VIBAFlex, VIBA Sinterflex, etc.), suitable for construction joints in walls in accordance with DIN EN 1992-1-1/NA. The sealing is made by the waterstop seal sheet. The formwork consists of a stable, fine-meshed expanded metal, which, in the keyed version, is profiled in accordance with DIN EN 1992-1-1/NA. The elements feature a slot for accommodating the waterstop sheet to be installed on site.
69SV Vario Formwork Strip for Recesses On site, the corrugated formwork strips are unrolled from the roll to the required length for the recess and can be cut to size easily by bending them back and forth along the transverse perforation. • Minimal installation time for creating recesses (only a few minutes). • No stripping required after the concrete has cured (lost formwork). • Virtually no material waste, as any remaining strip can be attached to a new roll and reused.
Stop end panel made of a wave-profiled perforated metal plate in order to set a stop end in the wall or in the bottom plate.
Element size 250 x 60 cm Used as permanent formwork in concrete and reinforced concrete construction. Longitudinal ribs ensure high load-bearing capacity. Strong bonding effect through stong surface profiling. Great stability thanks to 10 mm high ribs and bead reinforcement. Very cost-effective because there is no need to remove or clean the formwork
Used as shuttering formwork in concrete and reinforced concrete construction. Longitudinal ribs ensure high load-bearing capacity. Strong composite effect becauce of the strong surface profiling. Particularly high stability thanks to 21 mm high ribs and bead reinforcement as well as a higher material thickness of 0.4 or 0.6 mm. Very cost-effective, as there is no need to remove or clean the formwork Element size 200 x 44.5 cm
Formwork stop made of fibreglass. Pins Ø: 10 mm; Length: 100 mm ADVANTAGES: Non-corrosive High strength and stable Chemical resistance Fast and easy installation INSTALLATION: Mark the position of the formwork with a snap line. Drill periodically holes with a diameter of 10mm along the marking. ATTENTION: Please consider the length of the pins.
Concrete form round in spiral version. Other lengths on request!
Vitzthum-water bars made of soft PVC bribe through many good features and high profitability. The water bars are resistant against acid, alkali and putrefaction. Bitumen-resistant variety on request! Variety overview: Typ a b c f k 61D150 150 70 3,0 10 10 61D200 200 90 3,5 15 10 61D250 240 90 4,0 15 20 61D300 320 110 5,0 15 20
Product properties: non-flammable passable insensitive to moisture frost-resistent easy perforation of openings Bulk density: 300 kg m³, +- 5% Compressive strength: 240 kPa (10% compression) Baustoffklasse: A2, s1, dO(ÖNORM EN 13501-1)