Formwork stop round with nail
Description
For fixing the formwork in the lower area.
PVC formwork stop with nail: With pre-assembled steel nail for quick assembly. Suitable for standard nail guns.
Ähnliche Artikel
For fixing the formwork in the lower area. PVC block: This stop is attached off-center with a steel nail and adjusted by turning, then fixed in the center.
Formwork stop made of fibreglass. Pins Ø: 10 mm; Length: 100 mm ADVANTAGES: Non-corrosive High strength and stable Chemical resistance Fast and easy installation INSTALLATION: Mark the position of the formwork with a snap line. Drill periodically holes with a diameter of 10mm along the marking. ATTENTION: Please consider the length of the pins.
Customers also viewed
For fixing the formwork in the lower area. PVC block: This stop is attached off-center with a steel nail and adjusted by turning, then fixed in the center.
Plastic basement windows Sash and frame made of high quality plastic Color white circumferential rubber seal Turn / tilt fitting Double glazing
The flexible, compressible PE Spiral Spacer Tube 22/28 has been specially developed for use in challenging formwork conditions. The spiral tube can be used in combination with a plastic spacer tube or an FB wall thickness spacer. It provides a practical and adaptable solution, particularly for single-sided formwork, uneven surfaces, and irregular tie rod positions, such as those encountered on rock faces or in excavation pits. Thanks to its special spiral structure, the tube can be compressed by applying axial pressure, allowing it to adapt flexibly to different spacing requirements. At the same time, it offers greater rigidity than conventional PE tubes. This makes it easier to unscrew and remove the formwork tie rod after concreting. Another advantage is the ease of adjusting its length: the spiral spacer tube can be cut to the required length directly on the construction site, even during formwork assembly, using a suitable cutting tool. With an internal diameter of 22 mm, the spiral tube is designed for use with Ø15 mm formwork tie rods.
Spacer tubes with a roughened surface from Ø 20mm to Ø 40 mm in bundlesØ 20mm to Ø 22mm 100 running meters per bundleØ 26mm to Ø 32mm 50 running meters per bundleØ 40mm 30 running meters per bundle
Plastic basement windows Sash and frame made of high quality plastic Color white circumferential rubber seal Turn / tilt fitting Double glazing
Spacer tubes with a roughened surface from Ø 20mm to Ø 40 mm in bundlesØ 20mm to Ø 22mm 100 running meters per bundleØ 26mm to Ø 32mm 50 running meters per bundleØ 40mm 30 running meters per bundle
Spacer tubes with a roughened surface from Ø 20mm to Ø 40 mm in bundlesØ 20mm to Ø 22mm 100 running meters per bundleØ 26mm to Ø 32mm 50 running meters per bundleØ 40mm 30 running meters per bundle
Spacer tubes with a roughened surface from Ø 20mm to Ø 40 mm in bundlesØ 20mm to Ø 22mm 100 running meters per bundleØ 26mm to Ø 32mm 50 running meters per bundleØ 40mm 30 running meters per bundle
One-piece formwork spacer tube with two sealing plugs, ensuring the specified wall thickness reliably. Spacer tube / cone system tested for watertightness up to 5 bar Fire resistance tested in accordance with EN 1363-1 Complies with the requirements of the W1 guideline
Customers also bought
With internal thread for Ø 15 mm Dywidag tension rod Borehole Ø 22 mm borehole depth 95 mm Permissible load capacity min. 17.0 kN with a minimum concrete strength of 15N / mm²
One-piece formwork spacer tube with two sealing plugs, ensuring the specified wall thickness reliably. Spacer tube / cone system tested for watertightness up to 5 bar Fire resistance tested in accordance with EN 1363-1 Complies with the requirements of the W1 guideline