Properties
| Ausführung: | aufklappbar |
|---|---|
| Medium pipe Ø: | 1 x 25,32,40 mm/ 3 x 6-18 mm |
Annular Seal - cable Ø 100 mm foldable
Product number:
61LXN10109
Available, delivery time: 1-3 days
Price on request
Properties
| Ausführung: | aufklappbar |
|---|---|
| Medium pipe Ø: | 1 x 25,32,40 mm/ 3 x 6-18 mm |
Downloads "Annular Seal - cable Ø 100 mm foldable"
Skip product gallery
Customers also viewed
Annular seal - cable Ø 100 mm solid
Annular seal - cable 5-fold Ø 100 mm MR 8-35 mm
Tested up to 10 m WS (1 bar)
Hinged annular seal for core drilling / wall sleeves Ø 100 mm
Segment ring technology for 1 cable / pipe Ø 22 - 44 mm
as well as 4 cables Ø 7-12 mm
completely gastight and watertight
Sealing width 40 mm, pressure-tight up to 1 bar
U-profile and screws made of stainless steel V2A
EPDM rubber insert
integrated blind plug
We expressly point out that if there are deviations from the information in the assembly instructions and if our products are used improperly, no guarantee is given for any consequential damage.
Log in to see more information
Seal "onion ring" technology Ø 100 mm - divisible MR Ø 18 - 65 mm
Super segment ring technology for cables and pipes; 12 segment rings with a diameter of 16 - 65 mm; simply tear off the segments until they fit
split design, suitable for subsequent installation
Seal width 40 mm, pressure-tight up to 1 bar
integrated torque control visible and tangible
U-profile and screws made of stainless steel V2A
EPDM rubber insert
integrated blind plug
Log in to see more information
Ringraumdichtung Basic 1 - Dichtungsbreite 40 mm
Annular seal Basic 1 made of stainless steel, V2A (material no.1.4301)
Seal width 40 mm for pressing water up to 2.5 bar
completley gastight and watertight
built-in torque control
EPDM rubber insert
DIVIDING THE RING SEAL BASIC 1
To split the annular seal Basic 1, loosen and remove a screw.
Unfold the front and rear press segment and cut the rubber press ring radially about 10 mm to the left or right of the screw hole with a sharp knife.
Log in to see more information
Seal "onion ring" technology Ø 100 mm - divisible MR Ø 25, 32, 40, 50 und 63 mm
Super segment ring technology for cables and pipes
Open the pipe seal. Cut into the selected segment rings at the predetermined separation point with a sharp knife and tear off
5 segment rings with a diameter of 25 - 63 mm
segment ring
Pipe area
Plug
Ø 25 - 28 mm
Nr. 1
Ø 32 mm
Nr. 2
Ø 40 mm
Nr. 3
Ø 50 mm
Nr. 4
Ø 63 mm
Log in to see more information
Ringraumdichtung P-Cable Basic HRD 200
The P-Cable Basic HRD annular seal is available in various designs.The following product identification is used:
SG x (number of holes) / y-z (area in mm which the hole can be adjusted)
Log in to see more information
Zwiebeldichtung Basic 1
Annular seal Basic 1 made of stainless steelStainless V2A
Seal width 40 mm
completely gastight and watertight
built-in torque control
EPDM rubber insert
To split the press seal Basic 1, loosen and remove a screw. Unfold the front and rear press segment and cut the rubber press ring approx. 10 mm to the left or right of the screw hole with a sharp knife.
Log in to see more information
Ringraumdichtung P-Cable Basic HRD 125
The P-Cable Basic HRD annular seal is available in various designs.The following product identification is used:
SG x (number of holes) / y-z (area in which the hole can be adjusted)
Log in to see more information
Seal "onion ring" technology Ø 150 mm - fixed type 1 MR Ø 32, 40, 50, 63, 76, 90, 110 mm
Seal for pressing and non-pressing water
Tested for continuous use up to 30 m water column
Press plates and screws made of V2A stainless steel
Sealing width 40 mm
NBR rubber insert
Temperature range -30 ° C to + 120 ° C
Log in to see more information
Zwiebeldichtung Basic 1
Annular seal Basic 1 made of stainless steelStainless V2A
Seal width 40 mm
completely gastight and watertight
built-in torque control
EPDM rubber insert
To split the press seal Basic 1, loosen and remove a screw. Unfold the front and rear press segment and cut the rubber press ring approx. 10 mm to the left or right of the screw hole with a sharp knife.
Log in to see more information
Zwiebeldichtung Basic 1
Annular seal Basic 1 made of stainless steelStainless V2A
Seal width 40 mm
completely gastight and watertight
built-in torque control
EPDM rubber insert
To split the press seal Basic 1, loosen and remove a screw. Unfold the front and rear press segment and cut the rubber press ring approx. 10 mm to the left or right of the screw hole with a sharp knife.
Log in to see more information