Properties

Breite in mm:	300 mm

Universal-scrapers 300 mm

Product number: 51A300

Breite in mm

150 mm

300 mm

500 mm

Stk

Description

Width: 300 mm
Height: 160 mm
with shaft

Properties

Breite in mm:	300 mm

Variants

With the help of our variant list you can find your article faster and easier.

Product Nr.	Product	Breite in mm
51A150	Universal-scrapers 150 mm	150 mm
51A300	Universal-scrapers 300 mm	300 mm
51A500	Universal-scrapers 500 mm	500 mm

Product Nr. : 51A150

Universal-scrapers 150 mm

Price

Breite in mm: 150 mm

In Stock

Available, delivery time: 1-3 days

Product Nr. : 51A300

Universal-scrapers 300 mm

Price

Breite in mm: 300 mm

In Stock

Available, delivery time: 1-3 days

Product Nr. : 51A500

Universal-scrapers 500 mm

Price

Breite in mm: 500 mm

In Stock

Available, delivery time: 1-3 days

Zubehör

Replacement blade for scraper

Replacement blade for scraper 150 mm

Replacement blade

Customers also viewed

Universal-scrapers 150 mm

Width: 150 mm Height: 160 mm with shaft

Universal-scrapers 500 mm

Width: 500 mm Height: 160 mm with shaft made of beechwood

Sylomer-Polyurethanlager SR110

Sylomer sound bearing bearing type SR110 Area of application Pressure load Deformation Form factor dependent, the specified values apply to form factor q = 3 Static area of application(static loads) up to 0,110 N/mm² approx. 10 % Dynamic area of application(static and dynamic loads) up to 0,160 N/mm² approx. 20% Peak loads(rare, short-term loads) up to 3,0 N/mm² approx. 70%

Bolzen- und Mattenschneider

For commercial reinforcing steel III + IV according to DIN 488 strength approx. 550 N / mm2 as well as prestressing steels and tempered steel wire up to a strength of 1570 N / mm2 (48 HRc) Please note the following when using the bolt cutters: Our bolt cutters are made of the best material. Make sure that the knives are placed at a right angle to the piece to be cut. Stronger structural steels must not be cut through at once. They must first be pressed in firmly, after which the bolt cutter is opened and pushed in again. This makes cutting easier and prevents the knives from breaking. After pressing in, the bolt cutter must not be levered, swiveled or inclined as this would lead to the cutting edges breaking out. The bolt cutters must never be used for hardened steels, concrete or steel nails. The service life of the bolt cutters is enormously extended by regularly tightening the screws.

Protective mats Super (frost protection)

The protective mats SUPER is bothsided coated with a white layer (Summer side) and a black layer (Winter side) Scope of application: Frost protection for Winter (enables concrete work to -5 Degree C without hardness decrease) Evaporation protection Protective covering Heat insulation

Deckenrandschalung XPS 50 FZ ISO

Slab edge shuttering and insulation in one. 50 mm extruded polystyrene. Foot is made of 4mm fibre cement (Width 10 cm) Elements with tongue and groove. Standard in 1 or 2 metre elements, other lengths on request.

ZZ-batten

Skidproofed and tilt secured spacer for the bottom reinforcement. There will be no shrinking as the concrete encloses the batten completly. Due to the special form a linear interruption can be avoided. Mill lenghts 200 cm. Other lenghts available.

Deckenrandschalung XPS 50 FZ ISO

Abstandrohre mit aufgerauter Oberfläche von Ø 20mm bis Ø 40mm in Bunden. Standardlänge ist 2,0 Meter.

Spacer tubes with a roughened surface

Spacer tubes with a roughened surface from Ø 20mm to Ø 40 mm in bundlesØ 20mm to Ø 22mm 100 running meters per bundleØ 26mm to Ø 32mm 50 running meters per bundleØ 40mm 30 running meters per bundle

ZZ-batten