Scaffolding board (wood covering) - door
Product number:
39GA02
Skip product gallery
Zubehör
Gerüstplatte (Holzbelag)
Repeatedly glued wood cover plate.
Double security by glueing and with iron rod.
Galvanized edges protection in both sides, for a long lifespan in the hard application.
Log in to see more information
Skip product gallery
Ähnliche Artikel
Access ladder for scaffolding lacquered G0470
Used in conjunction with the wooden panel with door
The internal staircase enables safe and convenient access to the scaffolding
available lacquered or hot-dip galvanized
Delivery is WITHOUT wooden panel with door
Skip product gallery
Customers also viewed
Gerüstplatte (Holzbelag)
Repeatedly glued wood cover plate.
Double security by glueing and with iron rod.
Galvanized edges protection in both sides, for a long lifespan in the hard application.
Access ladder for scaffolding lacquered G0470
Used in conjunction with the wooden panel with door
The internal staircase enables safe and convenient access to the scaffolding
available lacquered or hot-dip galvanized
Delivery is WITHOUT wooden panel with door
Deckenstütze Euro (DO) nach EN 1065
Produced and tested according to EN 1065, with visible thread (DO).
With failure protection and accident proof.
Headplate: 120 x 120 x 8 mm, with borehole Ø 40 mm
Headplate: * 140 x 140 x 8 mm, with borehole Ø 40 mm
G-hook: Ø 15 mm (no loosing).
Deckenstütze Euro (DO) nach EN 1065
Produced and tested according to EN 1065, with visible thread (DO).
With failure protection and accident proof.
Headplate: 120 x 120 x 8 mm, with borehole Ø 40 mm
Headplate: * 140 x 140 x 8 mm, with borehole Ø 40 mm
G-hook: Ø 15 mm (no loosing).
Bolzen- und Mattenschneider
For commercial reinforcing steel III + IV according to DIN 488 strength approx. 550 N / mm2 as well as prestressing steels and tempered steel wire up to a strength of 1570 N / mm2 (48 HRc)
Please note the following when using the bolt cutters:
Our bolt cutters are made of the best material. Make sure that the knives are placed at a right angle to the piece to be cut. Stronger structural steels must not be cut through at once. They must first be pressed in firmly, after which the bolt cutter is opened and pushed in again. This makes cutting easier and prevents the knives from breaking. After pressing in, the bolt cutter must not be levered, swiveled or inclined as this would lead to the cutting edges breaking out. The bolt cutters must never be used for hardened steels, concrete or steel nails. The service life of the bolt cutters is enormously extended by regularly tightening the screws.
Log in to see more information
Baustütze - Mini (DC)
With covered thread (DC).
Headplate: 120 x 120 x 5 mm, with borehol ø 40 mm
G-hook: Ø 12 mm (no loosing) with bearing ring (loose)
Failure loads tested at concentric load, pay attention to security factor!
Lager- und Transportgestell
Easy storage of 25 or 30 fields and feet
Ideal for rental at events and on construction sites
Can be transported by forklift or crane
Deckenstütze Euro (DO) nach EN 1065
Produced and tested according to EN 1065, with visible thread (DO).
With failure protection and accident proof.
Headplate: 120 x 120 x 8 mm, with borehole Ø 40 mm
Headplate: * 140 x 140 x 8 mm, with borehole Ø 40 mm
G-hook: Ø 15 mm (no loosing).
Deckenstütze Euro (DO) nach EN 1065
Produced and tested according to EN 1065, with visible thread (DO).
With failure protection and accident proof.
Headplate: 120 x 120 x 8 mm, with borehole Ø 40 mm
Headplate: * 140 x 140 x 8 mm, with borehole Ø 40 mm
G-hook: Ø 15 mm (no loosing).
