Properties
| Ausführung: | lackiert |
|---|---|
| Länge in cm: | 175 cm |
Access ladder for scaffolding lacquered G0470
Product number:
39GL55
Properties
| Ausführung: | lackiert |
|---|---|
| Länge in cm: | 175 cm |
Skip product gallery
Ähnliche Artikel
Scaffolding board (wood covering) - door
Repeatedly glued wood cover plate.
Double security by glueing and with iron rod.
Galvanized edges protection in both sides, for a long lifespan in the hard application.
Skip product gallery
Customers also viewed
Gerüstplatte (Holzbelag)
Repeatedly glued wood cover plate.
Double security by glueing and with iron rod.
Galvanized edges protection in both sides, for a long lifespan in the hard application.
Half frame 1 m x 0,65 lacquered G0150
Half frame 1,0 x 0,65 cm from tubes 48 x 2,3 mm.
All stand parts are varnished or hot-dip galvanized available.
Version corresponds ÖNORM B 4007 and HD 1000.
Scaffolding board (wood covering) - door
Repeatedly glued wood cover plate.
Double security by glueing and with iron rod.
Galvanized edges protection in both sides, for a long lifespan in the hard application.
Gerüstplatte (Holzbelag)
Repeatedly glued wood cover plate.
Double security by glueing and with iron rod.
Galvanized edges protection in both sides, for a long lifespan in the hard application.
Deckenstütze Euro (DO) nach EN 1065
Produced and tested according to EN 1065, with visible thread (DO).
With failure protection and accident proof.
Headplate: 120 x 120 x 8 mm, with borehole Ø 40 mm
Headplate: * 140 x 140 x 8 mm, with borehole Ø 40 mm
G-hook: Ø 15 mm (no loosing).
Shifting frame lacquered
Shifting fram made of tube 48 x 2,3 mm
The shifting frame for extremely high steps (e.g. stairwells)
All variants in lacquered or of galvanized version available!
Deckenstütze Euro (DO) nach EN 1065
Produced and tested according to EN 1065, with visible thread (DO).
With failure protection and accident proof.
Headplate: 120 x 120 x 8 mm, with borehole Ø 40 mm
Headplate: * 140 x 140 x 8 mm, with borehole Ø 40 mm
G-hook: Ø 15 mm (no loosing).
Bolzen- und Mattenschneider
For commercial reinforcing steel III + IV according to DIN 488 strength approx. 550 N / mm2 as well as prestressing steels and tempered steel wire up to a strength of 1570 N / mm2 (48 HRc)
Please note the following when using the bolt cutters:
Our bolt cutters are made of the best material. Make sure that the knives are placed at a right angle to the piece to be cut. Stronger structural steels must not be cut through at once. They must first be pressed in firmly, after which the bolt cutter is opened and pushed in again. This makes cutting easier and prevents the knives from breaking. After pressing in, the bolt cutter must not be levered, swiveled or inclined as this would lead to the cutting edges breaking out. The bolt cutters must never be used for hardened steels, concrete or steel nails. The service life of the bolt cutters is enormously extended by regularly tightening the screws.
Log in to see more information
Bolzen- und Mattenschneider
For commercial reinforcing steel III + IV according to DIN 488 strength approx. 550 N / mm2 as well as prestressing steels and tempered steel wire up to a strength of 1570 N / mm2 (48 HRc)
Please note the following when using the bolt cutters:
Our bolt cutters are made of the best material. Make sure that the knives are placed at a right angle to the piece to be cut. Stronger structural steels must not be cut through at once. They must first be pressed in firmly, after which the bolt cutter is opened and pushed in again. This makes cutting easier and prevents the knives from breaking. After pressing in, the bolt cutter must not be levered, swiveled or inclined as this would lead to the cutting edges breaking out. The bolt cutters must never be used for hardened steels, concrete or steel nails. The service life of the bolt cutters is enormously extended by regularly tightening the screws.
Log in to see more information