Properties

Länge in mm:	920 mm

Bolzen- und Mattenschneider

Product number: 99D920ST

Länge in mm

780 mm

920 mm

Product request

Salutation

First name*

Last name*

Company name*

Phone number

E-Mail-Address*

Quantity*

Stk

Bolzen- und Mattenschneider

Länge in mm: 920 mm

Message

Fields marked with asterisks (*) are required.

(Product number: 99D920ST)

Description

For commercial reinforcing steel III + IV according to DIN 488 strength approx. 550 N / mm2 as well as prestressing steels and tempered steel wire up to a strength of 1570 N / mm2 (48 HRc)

Please note the following when using the bolt cutters:

Our bolt cutters are made of the best material. Make sure that the knives are placed at a right angle to the piece to be cut. Stronger structural steels must not be cut through at once. They must first be pressed in firmly, after which the bolt cutter is opened and pushed in again. This makes cutting easier and prevents the knives from breaking. After pressing in, the bolt cutter must not be levered, swiveled or inclined as this would lead to the cutting edges breaking out. The bolt cutters must never be used for hardened steels, concrete or steel nails. The service life of the bolt cutters is enormously extended by regularly tightening the screws.

Properties

Länge in mm:	920 mm

Variants

With the help of our variant list you can find your article faster and easier.

Product Nr.	Product	Länge in mm
99D780ST	Bolzen- und Mattenschneider	780 mm
99D920ST	Bolzen- und Mattenschneider	920 mm

Product Nr. : 99D780ST

Bolzen- und Mattenschneider

Price

Länge in mm: 780 mm

In Stock

Available, delivery time: 1-3 days

Product Nr. : 99D920ST

Bolzen- und Mattenschneider

Price

Länge in mm: 920 mm

In Stock

Available, delivery time: 1-3 days

Customers also viewed

Universal-scrapers 300 mm

Width: 300 mm Height: 160 mm with shaft

Sylomer-Polyurethanlager SR110

Sylomer sound bearing bearing type SR110 Area of application Pressure load Deformation Form factor dependent, the specified values apply to form factor q = 3 Static area of application(static loads) up to 0,110 N/mm² approx. 10 % Dynamic area of application(static and dynamic loads) up to 0,160 N/mm² approx. 20% Peak loads(rare, short-term loads) up to 3,0 N/mm² approx. 70%

Bolzen- und Mattenschneider

For commercial reinforcing steel III + IV according to DIN 488 strength approx. 550 N / mm2 as well as prestressing steels and tempered steel wire up to a strength of 1570 N / mm2 (48 HRc) Please note the following when using the bolt cutters: Our bolt cutters are made of the best material. Make sure that the knives are placed at a right angle to the piece to be cut. Stronger structural steels must not be cut through at once. They must first be pressed in firmly, after which the bolt cutter is opened and pushed in again. This makes cutting easier and prevents the knives from breaking. After pressing in, the bolt cutter must not be levered, swiveled or inclined as this would lead to the cutting edges breaking out. The bolt cutters must never be used for hardened steels, concrete or steel nails. The service life of the bolt cutters is enormously extended by regularly tightening the screws.

PAE-Construction foil

Other widths and strengths on request. Rated strength less usual tolerance.

Protective mats Super (frost protection)

The protective mats SUPER is bothsided coated with a white layer (Summer side) and a black layer (Winter side) Scope of application: Frost protection for Winter (enables concrete work to -5 Degree C without hardness decrease) Evaporation protection Protective covering Heat insulation

Unischaber HM

Universal scrapers with embedded hard metal indexable inserts and bent push knife from special steel. Handle length 850 or 1300 mm. Simple replaceable shee from quality spring steel. Knot-free handle.

Construction foil (frost protection)

Material: Composite foil made of 100% polypropylene fibre, laminated with UV- stabil Polyethylen (LDPE-foil). The construction foil ist one sided laminated with black foil. Characteristics: tear-resistant and doesn't rot high resistance against mechanical damage good heat insulation full recyclable multiplicative reusable Applications:Evaporation protection, cold protection, Protection of thinning by wet concrete, conservation plan.

PVC anchor

Very stable anchor or nail made of synthetic material for fastener von isulating material.

PE wall damp course

The damp proof courses protect the masonry from rising moisture. Both sides of the material are ripped and increase the liability to the mortar. Material: Polyethylen, slip-resistant; Thickness: ca. 0,4 mm.

Fleece Geotextile

Geotex is a mechanic strengthend fleece to split and filter.Main application is gravel, passably and grassed flat roofs. What can Geotex - fleece? Geotex seperate the particle to allow unhindered drain of water. The fleece prevent, even by high drain amount, blockage.