Wheelbarrow type 79961 with ball bearing

Wheelbarrow type 79963 polymere bearing wheel

Edge of through reinforced with complete round bar. Fastening-screws invisible. Steel-rim wheel 400 x 100 mm. On demand with polymer solid-rubber wheel.

Kunststoff - Fenster ohne Schalung DKI

Plastic basement windows Sash and frame made of high quality plastic Color white circumferential rubber seal Turn / tilt fitting Double glazing

Bolzen- und Mattenschneider

For commercial reinforcing steel III + IV according to DIN 488 strength approx. 550 N / mm2 as well as prestressing steels and tempered steel wire up to a strength of 1570 N / mm2 (48 HRc) Please note the following when using the bolt cutters: Our bolt cutters are made of the best material. Make sure that the knives are placed at a right angle to the piece to be cut. Stronger structural steels must not be cut through at once. They must first be pressed in firmly, after which the bolt cutter is opened and pushed in again. This makes cutting easier and prevents the knives from breaking. After pressing in, the bolt cutter must not be levered, swiveled or inclined as this would lead to the cutting edges breaking out. The bolt cutters must never be used for hardened steels, concrete or steel nails. The service life of the bolt cutters is enormously extended by regularly tightening the screws.

Aussparungs-Innenecken

Inner corner made of steel with clamping screws Ø 15 mm For shaft formwork, ceilings- door- and wall-recess Easy and fast mounting and dismantling For wooden formwork 12 - 35 mm thickness The fast and universal solution for your construction site

Barelle für Deckenstützen

These barelles are especially suitable for the efficient transport and storage of ceiling props. Suitable for crane and forklift operation (4 crane hooks on the side). Easy stacking because of the Conical bell feet Made from steel tubes with a diameter of 48 mm. Dimensions L W H are clear dimensions

Deckenstützen Euro (DC) nach EN 1065

All versions with failure protection, accident proof. Props in different sizes and versions.Failure loads tested according to EN 1065. Produced and tested according to EN 1065, with covered thread (DC). With failure protection and accident proof. Threaded socket with additional bearing ring (slide ring). Headplate: class A 120 x 120 x 8 mm, with borehole Ø 40 mm G-hook: Ø 14 mm (no loosing) with bearing ring.

Contact adhesive CEM 805 for swelling waterstop and joint sealing strip

CEM805 is a one-component, neutral-odor sealing and bonding compound based on MS hybrid polymer technology. It is solvent-free, silicone-free and isocyanate-free, cures neutrally, is paint-compatible, weather-resistant and offers good chemical resistance. Applications:Contact adhesive CEM805 is used as a system sealant and installation adhesive for hydrophilic waterstops, joint sealing sheets and concrete plugs. Typical applications include: Sealing and bonding in concrete construction for interior and exterior use Tested for watertightness up to 5.0 bar hydrostatic water pressure (= 50 m water column) in the DualProof System (PVC-P), at product transitions and on concrete surfaces Crack-bridging up to 2.50 mm down to -35°C (crack-bridging class A5) Crack-bridging sealant up to 50 m water column Suitable for use on plaster, gypsum, ceramic, glass, wood, metal and various plastic substrates, as well as galvanized steel and aluminum Well suited for bonding construction foils and membranes Suitable for sealing and bonding applications requiring silicone-free systems on site Butt joint bonding of SilverSeal using CEM805 has been tested and proven watertight up to 2.5 bar (= 25 m water column) Hydrophilic joint tapes (Art. No. 61L) and swelling rubber profiles can be installed in a backflow-proof manner with CEM805 in accordance with German general building authority approval (abP) Also suitable for use with fresh concrete bonded waterproofing systems and joint sealing metal sheets. Note: Do not apply on substrates such as bitumen, tar or coatings that may cause incompatibilities and plasticizer migration. Standards and certification CEM805 contact adhesive is tested as a sealant in accordance with EN 15651-1 and certified as EC1Plus according to EMICODE. Product features and advantages: Ready-to-use MS polymer installation adhesive and sealant, free of silicone, isocyanates and solvents, with a broad adhesion spectrum Elastic Non-corrosive Neutral odor Weathering and aging resistant Good UV resistance Virtually no shrinkage No bubble formation Paint-compatible

Loop Anchor

To anchore single-sided system to the floor, to mount formwork element, A-frames, scaffolding bracket, etc. Design: Black

Diem- concrete mixer tilting drum type Allround D 120C

Ahead of its time with the latest compact generation. Professionals use this concrete mixer Convenient operationThe most important operating elements such as toggle levers and switches are arranged in a user-friendly manner. Optimal size of the flanged drum openingExcellent accessibility and practical drainage of the concrete. Light and power connection innovatively combined in one machinePromises versatility on every construction site - 230V and 400V! Tried and tested chassisThe mobility on construction site terrain is guaranteed. The specially designed concrete mixer guarantees excellent mixing results. The tilting mixers drum type of the compact generation are extremely robust and maintenance-free, perfectly suited for daily construction site operations. Technical specifications: Motor 230/400V 0,75 KW Transmission 27 ¹ / min Capacity 180 l Mixing quantity 120 l Total heigth 1535 mm Total width 943 mm Total length 1350 mm Drum diameter 643 mm Drum heigth 631 mm Tilting gear - Weigth 151 kg Varnishing RAL 1013 Set of tiers Solid rubber

Unischaber HM

Universal scrapers with embedded hard metal indexable inserts and bent push knife from special steel. Handle length 850 or 1300 mm. Simple replaceable shee from quality spring steel. Knot-free handle.

Wheelbarrow type 79961 with ball bearing

Description