Barelle Gitterbox

Made from a sturdy tubular construction with four crane hooks, welded-in grid frame 50/50/5 mm and trapezoidal sheet metal floor.Load capacity: 1500 kg. Can be combined with our stacking racks.

These barelles are especially suitable for the efficient transport and storage of ceiling props. Suitable for crane and forklift operation (4 crane hooks on the side). Easy stacking because of the Conical bell feet Made from steel tubes with a diameter of 48 mm. Dimensions L W H are clear dimensions

Stackable transport container, load capacity 1500 kg Suitable for crane and forklift operation (4 lifting eyes above) Side walls made of grid mesh 50 x 50 x 4 mm Trapezoidal sheet metal floor Versions in painted or galvanized.

All versions with failure protection, accident proof. Props in different sizes and versions.Failure loads tested according to EN 1065. Produced and tested according to EN 1065, with covered thread (DC). With failure protection and accident proof. Threaded socket with additional bearing ring (slide ring). Headplate: class A 120 x 120 x 8 mm, with borehole Ø 40 mm G-hook: Ø 14 mm (no loosing) with bearing ring.

CEM805 is a one-component, neutral-odor sealing and bonding compound based on MS hybrid polymer technology. It is solvent-free, silicone-free and isocyanate-free, cures neutrally, is paint-compatible, weather-resistant and offers good chemical resistance. Applications:Contact adhesive CEM805 is used as a system sealant and installation adhesive for hydrophilic waterstops, joint sealing sheets and concrete plugs. Typical applications include: Sealing and bonding in concrete construction for interior and exterior use Tested for watertightness up to 5.0 bar hydrostatic water pressure (= 50 m water column) in the DualProof System (PVC-P), at product transitions and on concrete surfaces Crack-bridging up to 2.50 mm down to -35°C (crack-bridging class A5) Crack-bridging sealant up to 50 m water column Suitable for use on plaster, gypsum, ceramic, glass, wood, metal and various plastic substrates, as well as galvanized steel and aluminum Well suited for bonding construction foils and membranes Suitable for sealing and bonding applications requiring silicone-free systems on site Butt joint bonding of SilverSeal using CEM805 has been tested and proven watertight up to 2.5 bar (= 25 m water column) Hydrophilic joint tapes (Art. No. 61L) and swelling rubber profiles can be installed in a backflow-proof manner with CEM805 in accordance with German general building authority approval (abP) Also suitable for use with fresh concrete bonded waterproofing systems and joint sealing metal sheets. Note: Do not apply on substrates such as bitumen, tar or coatings that may cause incompatibilities and plasticizer migration. Standards and certification CEM805 contact adhesive is tested as a sealant in accordance with EN 15651-1 and certified as EC1Plus according to EMICODE. Product features and advantages:  Ready-to-use MS polymer installation adhesive and sealant, free of silicone, isocyanates and solvents, with a broad adhesion spectrum Elastic Non-corrosive Neutral odor Weathering and aging resistant Good UV resistance Virtually no shrinkage No bubble formation Paint-compatible

Pull out lever to remove the end of spacer after stripping the formwork. Suitable for normal and exposed concrete.

Infinite adjustment with two wedges Fast stripping Stronger version for all concrete works Wedges saved with chain

Infinite adjustment with two wedges Fast stripping Stronger version for all concrete works Wedges saved with chain

to pull out the spacer-end after stripping the formwork. Suitable for normal concrete and exposed concrete.

Spacer system SAM for normal concrete.(no exposed concrete surface - the walls should be plastered or coverd afterwards) Easy and fast application, in combination with 27 mm Standard formwork panels. Package units:to wall thickness 50 cm 100 pcs. / Packfrom wall thickness 51 cm 50 pcs. / Pack Other special lengths (in cm downgrading) from 6 - 300 cm possible.